Appareil portable pour la mesure de l’humidité dans l’huile
Oilport 30 Set
L'appareil de mesure portable Oilport 30 est utilisé pour la surveillance de l'humidité et de la température dans différentes huiles. Une utilisation simple et intuitive via l'écran tactile TFT et une fonction d'enregistrement intégrée font de l'Oilport 30 l'outil portable idéal pour des analyses d'huiles simples et fiables.
Valeurs mesurées
- Humidité relative / activité de l'eau [aw]
- Humidité absolue [ppm]
- Température [°C / °F]
Tout comme dans un gaz, l'humidité contenue dans une huile peut être exprimée en humidité absolue en ppm ou en humidité relative aw.
- ppm (masse de l'eau / masse de l'huile)
- aw (quantité d'eau comparée à l'eau contenue dans un échantillon d'huile saturée). Une huile sans aucune trace d'eau a une valeur aw de 0, une huile complétement saturée d'eau a une valeur aw de 1.
Le Oilport 30 détermine toujours l'activité de l'eau aw et la température T. Si on lui rentre les paramètres spécifiques de l'huile, l'appareil peut calculer la quantité d'eau en ppm et l'afficher sur l'écran.
Les sondes
- Sonde de tenue en pression jusqu'à 20 bar
Couplée au kit d'assemblage par vanne à boule, la sonde peut être positionnée et retiree sans interrompre le flux d'huile.
- Sonde courte Ø12mm
Idéale pour une prise de mesure d'humidité rapide dans des échantillons d'huile.
-
Oilport 30 Set
-
Oilport 30 avec kit de montage par vanne à boule
-
Sonde courte pour Oilport 30
-
Sonde pour tenue en pression pour Oilport 30
Produits connexes
EE381
EE364
Omniport 30
Téléchargements Oilport 30 Set
Foire Aux Questions (FAQ)
No, coating is not available for the E+E MIO sensors.
The standard scope of supply of E+E MIO sensors includes an inspection certificate according DIN EN 10204 - 3.1. For details on calibration certificates please see our white paper "Calibration and Traceability in Measuring Technology".
The standard scope of supply of E+E MIO sensors includes an inspection certificate according DIN EN 10204 - 3.1. For details on calibration certificates please see our white paper "Calibration and Traceability in Measuring Technology".
The standard scope of supply of E+E MIO sensors includes an inspection certificate according DIN EN 10204 - 3.1. For details on calibration certificates please see our white paper "Calibration and Traceability in Measuring Technology".
The standard scope of supply of E+E MIO sensors includes an inspection certificate according DIN EN 10204 - 3.1. For details on calibration certificates please see our white paper "Calibration and Traceability in Measuring Technology".
The standard scope of supply of E+E MIO sensors includes an inspection certificate according DIN EN 10204 - 3.1. For details on calibration certificates please see our white paper "Calibration and Traceability in Measuring Technology".
Calibration for a specific oil is a laboratory procedure for determining the saturation curve of the oil. The saturation curve is described by two parameters (A and B). These parameters are used for setting up the moisture in oil sensor for correct calculation of the water content (ppm) out of the measured temperature and water activity (aw).
Calibration for a specific oil is a laboratory procedure for determining the saturation curve of the oil. The saturation curve is described by two parameters (A and B). These parameters are used for setting up the moisture in oil sensor for correct calculation of the water content (ppm) out of the measured temperature and water activity (aw).
Calibration for a specific oil is a laboratory procedure for determining the saturation curve of the oil. The saturation curve is described by two parameters (A and B). These parameters are used for setting up the moisture in oil sensor for correct calculation of the water content (ppm) out of the measured temperature and water activity (aw).
Calibration for a specific oil is a laboratory procedure for determining the saturation curve of the oil. The saturation curve is described by two parameters (A and B). These parameters are used for setting up the moisture in oil sensor for correct calculation of the water content (ppm) out of the measured temperature and water activity (aw).
Calibration for a specific oil is a laboratory procedure for determining the saturation curve of the oil. The saturation curve is described by two parameters (A and B). These parameters are used for setting up the moisture in oil sensor for correct calculation of the water content (ppm) out of the measured temperature and water activity (aw).
Sensor replacement is possible for the EE360 models with the ordering code including PC4 (pluggable probe). Please see the operation manual for detail and spare part code ordering guide.
Sensor replacement is possible for the EE360 models with the ordering code including PC4 (pluggable probe). Please see the operation manual for detail and spare part code ordering guide.
Sensor replacement is possible for the EE360 models with the ordering code including PC4 (pluggable probe). Please see the operation manual for detail and spare part code ordering guide.
Sensor replacement is possible for the EE360 models with the ordering code including PC4 (pluggable probe). Please see the operation manual for detail and spare part code ordering guide.
Sensor replacement is possible for the EE360 models with the ordering code including PC4 (pluggable probe). Please see the operation manual for detail and spare part code ordering guide.
No, coating is not available for the E+E MIO sensors.
No, coating is not available for the E+E MIO sensors.
No, coating is not available for the E+E MIO sensors.
No, coating is not available for the E+E MIO sensors.
No, mineral transformer oils from different manufacturers are quite similar. A and B parameters are the same.
No, mineral transformer oils from different manufacturers are quite similar. A and B parameters are the same.
No, mineral transformer oils from different manufacturers are quite similar. A and B parameters are the same.
No, mineral transformer oils from different manufacturers are quite similar. A and B parameters are the same.
No, mineral transformer oils from different manufacturers are quite similar. A and B parameters are the same.
Please see the cleaning instructions.