Calibrazione dell'umidità con calibratore di umidità

Link in einer Lightbox öffnen
  • Humidity

Humor 20

La calibrazione dell'umidità precisa, riproducibile e documentabile acquisisce un ruolo sempre maggiore. Il calibratore per umidità Humor 20 sviluppato dalla E+E è per ciò lo strumento ideale di riferimento.

  • Humor 20 humidity calibrator

  • Humor 20 humidity calibrator with autokit

  • Humor 20 humidity calibrator with EE10

    Esso può essere utilizzato sia per la calibrazione delle sonde a stecca sia anche per strumenti con dimensioni cubiche nel campo di umidità da 10...95% Ur.

    Il calibratore Humor 20 è ripercorribile sugli standard internazionali.
    Grazie al suo funzionamento lo strumento può essere fatto funzionare sotto le normali condizioni climatiche in laboratori. Come mezzo d'esercizio si necessitano solo acqua distillata, aria compressa esente di olio (10 bar) e una tensione di alimentazione tra 90...230V CA.

    Il funzionamento dello Humor 20 si basa sulla procedura fondamentale delle due pressioni ed è quindi simile agli strumenti utilizzati dagli enti di taratura nazionali.

    Dati Tecnici

    Lavoro
    10...95% Ur
    Misura incertezza
    0,3 - 0,9% Ur
    Stabilizzazione
    < 3 min/punto di misura
    Alimentazione
    90...230 V AC

    Downloads Humor 20

    Scheda tecnica
    Software di applicazione

    FAQ

    The Humor 20 scope of supply includes an inspection certificate according to DIN EN 10204 – 3.1 in the standard scope of supply. An accredited calibration certificate with specific test points is available upon request.

    Please mention that you require an accredited calibration certificate when inquiring for a new HUMOR 20 or when returning for service or re-calibration an existing Humor 20. The most common accredited certificate festure 3 calibration points (15/55/90%RH) or 5 calibration points (15/35/55/75/90%RH). Other certificates upon request.

    During normal operation mode, incease the humidity generated by the Humor 10 to the maximum by rotating the blue knob counter-clockwise. The HUMOR 20 display will show arround 100% RH, flashing. Open the cover of the distilled water tank and remove the cover from the calibration chamber. If the display shows is 100 %RH ±0.8%RH, the Humor 20 is within specifications. Is the reading is beyond 100 %RH ±0.8%RH please see the operation manual, chapter 6.4.

    This is the sensing head from the plausibility sensor from the HUMOR 20.

    By design, the temperature inside the measuring and the saturation cambers of the Humor 20 is uniform. By this, in the range 10 to 40°C the influence of the ambient temperature is negligible.

    With distilled water inside during transportation, the Humor 20 may be tilted max. 20°. If this cannot be assured, the water must be removed before transportation.

    The humidity generator requires a compressed airof max. 10 bar (145psi), filtered from particles > 0.1µm , with residual oil <0.01mg/m³

    The humidity generator requires distilled water. Do not ever fill in tap water, because it causes depositsin the piping and pressure regulators, which lead to malfunktion and eventually to the failure of Humor 20.

    When you plan to use the humidity generator again within 4 days we recommend to keep the it powered and the humidity level set to 100% rh. For a longer periods out og use, please remove the water and dry the humidity generator before switch of the power.

    Set the display switch to temperature

    A blinking display after rotationg the blue knob for setting a new RH level indicates that the new RH evel has not been reached yet. The display should stop blinking after about 3 minutes when reached the new RH point. For a longer (or continuously) blinking display please consult the HUMOR20 operation manual.

    Yes. Please contact E+E for details and availability.

    Vuoi sapere di più sui nostri prodotti?

    Errore: Impossibile caricare il modulo di contatto
    LinkedIn Logo